Browse Categories
EMMPT48 series MPPT solar charge controller(1)
The Explorer-NS series MPPT solar charge controlle(1)
MPPT solar charge controller eSmart4(1)
EXPLORER-M MPPT Solar Smart Digital Controller(15)
EXPLORER MPPT Solar Smart Digital Controller(12)
RUNNER MPPT Solar Smart Digital Controller(9)
GALAXY high power series MPPT solar controller(12)
MARS outdoor series MPPT solar controller(10)
eSMART series MPPT solar controller(23)
MASTER series MPPT solar controller(28)
(out of product)WISER series MPPT solar controller(12)
(out of production)Inverter SP Series 350W-20000W(110)
(out of production)I-Panda SPC Series Inverter(70)
(Has been removed)(517)
Contact us
Tel: + 86-755-23091101&+86-755-23091100  
Fax: + 86-755-23091102   
address: Floor 2, building A2, LiLang Software Park, No. 31, Bulan Road, Nanwan street, Longgang District, Shenzhen   
China Post code: 518000
Contact Now
Home > Products > (out of production)Inverter SP Series 350W-20000W > 7000W pure sine wave inverter-.....


7000W pure sine wave inverter-I-Panda SP inverter series7000W pure sine wave inverter-I-Panda SP inverter series7000W pure sine wave inverter-I-Panda SP inverter series7000W pure sine wave inverter-I-Panda SP inverter series

7000W pure sine wave inverter-I-Panda SP inverter series

  • Introduction
  • When under inversion mode,this series of inverters can be set to normal working mode and sleep mode. And when under utility mode, it has Auto Voltage Regulation (AVR) function, utility charging function (only when AC first) and UPS function (AC first or DC first, optional). This multifunction low frequency pure sine wave inverter, which has the advantages of stable quality, strong load-carrying ability and anti-poor environment ability, Long service life, is the second generation of our low frequency pure sine wave inverter.


1. Back-up UPS system for industrial,commercial, household,etc

2. Mobile power and standby power for areasthat are lack of utility.

3. Off-grid solar & wind power system

3.1 Simple Off-grid solar & wind powersystem

3.2 AC first Off-grid solar & windpower system

3.3 DC first Off-grid solar & windpower system



1. pure sine wave output, full power

2. CPU management and control,modulardesign

3. LCD display,can visually display variousparameters

4. Multifunction design,can set a varietyof working mode

5. External battery connection, convenientto expand use time and back-up power time; user can connect as many batteriesas needed

6. With super load carrying ability andhigh load capacity, this series of inverters can not only drive resistance load; but also various kinds ofinductive loads, such as motor, air 

conditioner, electric drills, fluorescentlamp, gas lamp, etc. It can drive almost any kinds of load.

7. Low frequency circuit design, goodsystem stability, low failure rate and long service life (under properoperation, it may be as long as 5 years)

8. Perfect protection: low voltageprotection, over voltage protection, overheat protection, short-circuitprotection, overloads protection; alarm alert

9. CE / EMC / LVD/ RoHS Approvals.

10. Two years warranty, life-long technicalsupports



1. Sole inversion function under inversion mode (only connected to battery ),can be set to normal operatingmode and sleep mode.

1.1 Normal working mode:FREQUNCY in the LCD display is setas 01. No matter whether there are AC loads connected to the inverter or not,the inverter’s outputterminal will always have voltage ready to supply power to the loads. Underthis mode, the LCD will be displayed as bellow:


1.2 Sleep mode:FREQUNCY in the LCD display is setas 02. If the power of the loads that connected to the inverter is lower than5% of the inverter’s rated power, there will be no output from the inverter. That is tosay, only the chip of inverter is working under such condition and the powerconsumption is only 1-6W; If the power of the loads that connected to theinverter is higher than 5% of the inverter’s rated power, then the inverterwill automatically start the inversion function and supply power to the loadswithin 5s. As shown below:

2. UPS function under utility mode(connected to battery and utility .Can beset as utility first, battery standby mode and battery first, utility standbymode).

2.1 Utility first, battery standby UPSmode: FREQUENCY in the LCD display is set as 01. When both utility and batteryare connected to the inverter, utility will supply power to the loads prior tothe battery. When utility is cut off, the battery will automatically continueto supply power after inversion.

Steps are as follows:

Step 1: When utility power is available, itwill output directly after voltagebeing stabilized and charge batteries at thesame time.

Step 2: When utility power is cut offsuddenly, the inverter will convert DC power to AC power automatically toensure uninterrupted power supply within 5ms.

Step 3: When utility power becomesavailable again, it will automatically transfer to utility supplying power toloads and charge batteries at the same time.

See Workflow as below:

LCD displayed as bellow:

2.2 Battery first, utility standby UPSmode: FREQUENCY in the LCD display is set as 03.  When both utility and battery are connectedto the inverter, battery will supply power to the loads prior to utility. Whenbattery capacity is not enough, utility will continue to supply powerautomatically.

Steps are as follows:

Step 1: When battery has enough power, itwill supply power to the loads directly

Step 2: When battery does not have enoughpower, it will automatically transfer to utility supplying power to the loads

Step 3: After the battery is fully charged(e.g. by solar or wind charge controller), it will then automatically transferto battery supplying power to the loads.

See Workflow as below.

LCD displayed as bellow :





Rated Output Capacity


Peak Power


Battery Voltage(DC)


Size W×D×H(mm)


Packing Size W×D×H(mm)


Net Weight (kg)


Gross Weight (kg)


General Parameter

Working Mode


Utility First, Battery Standby



Sleep Mode,no utility,load’s power higher than 5% of rated power, start to work automatically



Battery first, utility standby

AC Input


220V±35% or 110V+35%(optional)


50Hz±3% or 60Hz±3% (optional)

AC Output


220V±3% or 230V±3 or 240V±3% or 100V±3%

or 110V±3% (optional)


50Hz±0.5 or 60Hz±0.5 (optional)

Battery charge

AC Charge Current


Charge Time

Depend on battery capacity and quantity

Battery Protection

Automatic detection, Charge and discharge protection,Intelligent Management


Display Mode


Display Information

Input voltage,output voltage,output frequency,battery capacity,Load condition,Status Information

Output Wave Type

Pure sine wave output,waveform distortion rate≤3

Overload Ability

>120% 1 min,>130% 10s

Power Consumption

Sleep Mode


Normal Mode


Conversion Efficiency


Transfer Time

<5ms (AC to DC / DC to AC)


Overload output,short-circuit,high-voltage input,low-voltage input,overheat









The “optional” parameter can be set as percustomer’s requirement

The above is our standard parameter.Subject to change without prior notice.

We have our own professional inverter andcontroller R&D team and we provide technical support and OEM service.



Please refer to the outline design,technical documents, product brochures, etc.

Made by Engineering Department  May 5, 2014 2nd Edition

Shenzhen ipandee New Energy Technology & Science Co., Ltd


Contact Person:Henry Feng

Send your inquiry directly to us
show code on cursor in the input box
( 0 / 3000 )