2000W pure sine wave inverter-I-Panda SP inverter series2000W pure sine wave inverter-I-Panda SP inverter series2000W pure sine wave inverter-I-Panda SP inverter series2000W pure sine wave inverter-I-Panda SP inverter series

2000W pure sine wave inverter-I-Panda SP inverter series

  • Introduction
  • When under inversion mode,this series of inverters can be set to normal working mode and sleep mode. And when under utility mode,it has Auto Voltage Regulation (AVR) function, utility charging function (only when AC first) and UPS function (AC first or DC first,optional). This multifunction low frequency pure sine wave inverter, which has the advantages of stable quality, strong load-carrying ability and anti-poor environment ability, Long service life, is the second generation of our low frequency pure sine wave  inverter.
Application

1. Back-up UPS system for industrial, commercial, household,etc

2. Mobile power and standby power for areas that are lack of utility.

3. Off-grid solar & wind power system

3.1 Simple Off-grid solar & wind power system

3.2 AC first Off-grid solar & wind power system

3.3 DC first Off-grid solar & wind power system


Features

1. pure sine wave output, full power

2. CPU management and control,modular design

3. LCD display,can visually display various parameters

4. Multifunction design,can set a variety of working mode

5. External battery connection, convenient to expand use time and back-up power time; user can connect as many batteries as needed

6. With super load carrying ability and high load capacity, this series of  inverters can not only drive resistance load; but also various kinds of inductive loads, such as motor, air conditioner, electric drills, fluorescent lamp, gas lamp, etc. It can drive almost any kinds of load

7. Low frequency circuit design, good system stability, low failure rate and long service life (under proper operation, it may be as long as 5 years)

8. Perfect protection: low voltage protection, over voltage protection, overheat protection, short-circuit protection, overloads protection; alarm alert

9. CE / EMC / LVD/ RoHS Approvals.

10. Two years warranty, life-long technical supports


Function

1.  Sole inversion function under inversion mode (only connected to battery),can be set to normal operating mode and sleep mode.



1.1 Normal working mode:FREQUNCY in the LCD display is set as 01. No matter whether there are AC loads connected to the inverter or not, the inverter’s output terminal will always have voltage ready to supply power to the loads. Under this mode, the LCD will be displayed as bellow: 

                                   
1.2 Sleep mode:FREQUNCY in the LCD display is set as 02. If the power of the loads that connected to the inverter is lower than 5% of the inverter’s rated power, there will be no output from the inverter. That is to say, only the chip of inverter is working under such condition and the power consumption is only 1-6W; If the power of the loads that connected to the inverter is higher than 5% of the inverter’s rated power, then the inverter will automatically start the inversion function and supply power to the loads within 5s. As shown below:

          
2.  UPS function under utility mode(connected to battery and utility .Can be set as utility first, battery standby mode and battery first, utility standby mode).



2.1 Utility first, battery standby UPS mode: FREQUENCY in the LCD display is set as 01. When both utility and battery are connected to the inverter, utility will supply power to the loads prior to the battery. When utility is cut off, the battery will automatically continue to supply power after inversion.

Steps are as follows:

Step 1: When utility power is available, it will output directly after voltagebeing stabilized and charge batteries at the same time.

Step 2: When utility power is cut off suddenly, the inverter will convert DC power to AC power automatically to ensure uninterrupted power supply within 5ms.

Step 3: When utility power becomes available again, it will automatically transfer to utility supplying power to loads and charge batteries at the same time.

See Workflow as below. 
 


LCD displayed as bellow:



2.2 Battery first, utility standby UPS mode: FREQUENCY in the LCD display is set as 03.  When both utility and battery are connected to the inverter, battery will supply power to the loads prior to utility. When battery capacity is not enough, utility will continue to supply power automatically. 

Steps are as follows: 

Step 1: When battery has enough power, it will supply power to the loads directly 

Step 2: When battery does not have enough power, it will automatically transfer to utility supplying power to the loads 

Step 3: After the battery is fully charged (e.g. by solar or wind charge controller), it will then automatically transfer to battery supplying power to the loads. 

See Workflow as below.



LCD displayed as bellow:



parameters

                                                        Mode                                                                                                                                                                              Parameter

3000VA

Rated Output Capacity

2000W

Peak Power

4000W

Battery Voltage(DC)

24V/48V/96V(optional)

Size W×D×H(mm)

350*220*460

Packing Size W×D×H(mm)

370*240*480

Net Weight (kg) 

23

Gross Weight (kg) 

25

General Parameter

Working Mode (Setting)

1

Utility First, Battery Standby

2

Sleep Mode,no utility,load’s power higher than 5% of rated power, start to work automatically

3

Battery first, utility standby

AC Input

Voltage

220V±35% or 110V+35%(optional)

Frequency

50Hz±3% or 60Hz±3% (optional)

AC Output

Voltage

220V±3% or 230V±3 or 240V±3% or 100V±3%

or 110V±3% (optional)

Frequency

50Hz±0.5 or 60Hz±0.5 (optional)

Battery charge

AC Charge Current

0~15A

Charge Time

Depend on battery capacity and quantity

Battery Protection

Automatic detection, Charge and discharge protection,Intelligent Management

Display

Display Mode

LCD

Display Information

Input voltage,output voltage,output frequency,battery capacity,Load condition,Status Information

Output Wave Type

Pure sine wave output,waveform distortion rate≤3

Overload Ability

>120% 1 min,>130% 10s

Power Consumption

Sleep Mode

1~6W

Normal Mode

1~3A

Conversion Efficiency

80%~90%

Transfer Time

<5ms (AC to DC / DC to AC)

Protection

Overload output,short-circuit,high-voltage input,low-voltage input,overheat

Environment

Temperature

-10℃~50℃

Humidity

 10%~90%

Altitude

≤4000m


Remark

The “optional” parameter can be set as per customer’s requirement

The above is our standard parameter. Subject to change without prior notice.

We have our own professional inverter and controller R&D team and we provide technical support and OEM service.


Others

Please refer to the outline design, technical documents, product brochures, etc.

Tag:
Shenzhen I-Panda New Energy Technology & Science Co., Ltd

Tel:+86-13652416749

Contact Person:Grace

Send your inquiry directly to us
( 0 / 3000 )