The high quality multifunction pure sine wave inverter I-Panda HPC series 1000WThe high quality multifunction pure sine wave inverter I-Panda HPC series 1000WThe high quality multifunction pure sine wave inverter I-Panda HPC series 1000WThe high quality multifunction pure sine wave inverter I-Panda HPC series 1000WThe high quality multifunction pure sine wave inverter I-Panda HPC series 1000W

The high quality multifunction pure sine wave inverter I-Panda HPC series 1000W

  • Application:
  • 1.Off-grid solar power system.
  • 2.Solar power system with utility as complementary power.

Introduction

This series of product is a module design of inverter and built-in MPPT controller, which has the advantages of high conversion efficiency, low power consumption and strong load-carrying ability. With intelligent control, customers can set charging mode, (Utility as complementary power) AC first mode or DC first mode, timed inversion mode and timed utility mode, timed on/off sleep mode. This is the currently the most advanced inverter & controller hybrid in the world.


Feature

1. Easy to install. To configure a solar system, customers only need to connect it with solar panels and batteries

2. CPU management ,intelligent control,modular design, User-friendly LCD display

3. Built-in MPPT controller, high charging efficiency

4. Low power consumption, high conversion efficiency

5. Intellectual,multi-function, convenient for customers with different using environment to fully use the solar energy

6. External battery connection, convenient to expand back-up power time

7. Strong load-carrying ability, low failure rate, easy maintenance and long service life (under proper operation, it may be as long as 5 years)

8.  Perfect protection: low voltage protection, over voltage protection, overheat protection, short-circuit protection, overloads protection

9. CE / EMC / LVD/ RoHS Approvals

10. Two years warranty, life-long technical supports

 

Function

1. Charging function

There are 2 modes as shown bellow:


1.1 PV charge the battery, utility will not: when PV and utility are both connected to the machine, only the PV will charge the battery when there is sunlight

1.2 Both PV and utility will charge the battery: when PV and utility are both connected to the machine, AC (utility) will charge the battery. In the meanwhile, PV will also charge the battery if there is sunlight.

 

2. Utility as complementary power function

There are 2 kinds of complementary modes, shown as bellow:


2.1  AC first , DC standby UPS mode

 

When both utility and battery are connected to the machine, utility will supply power to the loads prior to the battery. When utility is cut off, the battery will automatically continue to supply power.

 

Steps are as follows:

Step 1: When utility power is available, it will output directly after voltage being stabilized and charge batteries at the same time.

Step 2: When utility power is cut off suddenly, the inverter will convert DC power to AC power automatically to ensure uninterrupted power supply within 5ms.

Step 3: When utility power becomes available again, it will automatically transfer to utility supplying power to loads and charge batteries at the same time.

 

See Workflow as below:


2.2 DC first, AC standby UPS mode:

 

When both utility and battery are connected to the inverter, battery will supply power to the loads prior to utility. When battery capacity is not enough, utility will continue to supply power automatically.

 

Steps are as follows:

Step 1: When battery has enough power, it will supply power to the loads directly

Step 2: When battery does not have enough power, it will automatically transfer to utility supplying power to the loads

Step 3: After the battery is fully charged (e.g. by solar or wind charge controller), it will then automatically transfer to battery supplying power to the loads.

 

See Workflow as below.

3. Timing function

 

 There are 2 kinds of timing mode:

3.1  Timed on/off normal working mode and sleep mode: can set specific time when to open normal output and when to close AC output to enter sleep mode.

 

3.2  Battery and utility switchable mode: can set specific time when to use battery or utility supply power (suitable for areas where electric fee is charged according to period in different intervals)

 

4.  Recording/checking function


4.1 Machine fault checking: can check the machine fault information

4.2 Discharge time checking: can check the discharge time of the battery


Parameter

                                        Model

Parameter           

1000W

Rated Output Power

1000W

Peak Power

2000W

     Battery

(Lead-acid battery)

24V

Charging Parameter

Charge Mode(setting)

PV charge

PV charge + utility charge

MPPT Solar Controller

Voltage

24V

Current

20A

Max PV Input Voltage

100V

PV Charge Efficiency

95%~99%

Max PV Input Power

568W

Utility

AC Charge Current

0~15A

Charge Mode

3-Stage Charging

Inversion parameter

AC Output

Voltage

220V±3% or 230V±3 or 240V±3% or 100V±3%
or 110V±3% (optional)

Frequency

50Hz±0.5 or 60Hz±0.5 (optional)

Output wave type

Pure sine wave output, waveform distortion rate≤3

Overload ability

>120% 1 min, >130% 10s

Power Consumption

(under normal working mode)

0.4A

Power Consumption

(under sleep mode)

1-6W

Inverter Conversion Efficiency

85%~92%

Utility Mode

AC Input

Voltage

220V±35% or 110V+35%(optional)

Frequency

The same as utility

AC Output

Voltage

220V±5% or 110V+5%(optional)

Frequency

The same as utility

Overload Ability

>120% 1 min,>130% 10s

(AC first or DC first) priority

UPS Output(setting)

AC first, DC standby

DC first, AC standby

Switch Time

<5ms (AC to DC / DC to AC)

Power On
(setting)

Set by users

Timed open / close AC output automatically

General Parameter

Display

Display Mode

LCD+LED

Display Information

Input voltage, output voltage, output frequency, battery capacity, Load condition, Status Information

Protection

Overload output, short-circuit, high-voltage input, low-voltage input, overheat

 Environment

Temperature

-10℃~50℃

humidity

 10%~90%

Altitude

≤4000m

Size W×D×H(mm)

438*208*413

Packing Size W×D×H(mm)

520*310*460

Net Weight (kg)

15

Gross Weight (kg)

16


Remarks:

  • The “optional” parameter can be set as per customer’s requirement
  • The above is our standard parameter. Subject to change without prior notice.
  • We have our own professional inverter and controller R&D team and we provide technical support and OEM service.

Connection Diagram



Others

  • Please refer to the outline design, technical documents, product brochures, etc.
  • Made by Engineering Department, May 15, 2014, 2nd Edition
Tag:
Shenzhen I-Panda New Energy Technology & Science Co., Ltd

Tel:+86-13556898737

Contact Person:Eric Zhang

Send your inquiry directly to us
( 0 / 3000 )